USB 2.0 Cameras

 
USB 2.0  ...  Resolutions  (VGA • XGA • SXGA • SXGA • UXGA)    
 
 

 

STC-TB152USB-ASH

SXGA, Monochrome Camera

The STC-TB152USB-ASH is a compact, progressive scan, SXGA, USB cased camera with a 1/2” monochrome CCD, featuring 19fps, software and hardware triggering, image capture, digital zoom and a feature-rich user based menu setup and control. This series is available as a cased version with a rear mini USB connector. Sentech USB cameras include a SDK, DirectX, Twain and Linux driver, as well as the Sentech Viewing Software.
1/2" CCD Image Sensor, SXGA (1.3 Megapixel)
Signal Output over 12pin Connector, 19fps
Hardware & Software Trigger

 

Back    Front    Right    Left   

Select Options  
 

Name

Specifications
Model No
STC-TB152USB-ASH
Imager
½” Interline SXGA Monochrome Progressive CCD: ICX205AL
Total Picture Element
1434 (H) x 1050 (V)
Active Picture Element
1360 (H) x 1024 (V)
Chip Size
7.60 (H) x 6.20 (V) mm
Cell Size
4.65 (H) x 4.65 (V) μm
Scanning System
Progressive
Scanning Methods
Full Scanning, 1/1 Partial Scanning, ½ Partial Scanning, ¼ Partial Scanning, Variable Partial Scanning, Binning, Binning 1/1 Partial Scanning, Binning ½ Partial Scanning, Binning, ¼ Partial Scanning, Binning Variable Partial Scanning
Pixel Frequency
36.818 MHz
Maximum Frame Rate
- Full Scanning
19.26 fps
- 1/2 Partial
38.52 fps
- 1/4 Partial
77.04 fps
Resolution
1360 (H) x 1024 (V) (Full Scanning) 1360 (H) x 472 (V) (½ Partial Scanning) 1360 (H) x 176 (V) (¼ Partial Scanning)
S/N Ratio
≤ 10 digit (Factory Default Gain Setting)
Minimum Scene Illumination
0.12 Lux at F1.2
Sync System
Internal
Electronic Shutter
Auto / Manual (Software Selectable)
Gain
Auto / Manual (Software Selectable)
Gamma
Manual (Software Selectable)
White Balance
-
Trigger Mode
Free-run / Edge Preset Trigger / Pulse Width Trigger / Start & Stop Trigger (Software selectable)
Input / Output
USB2.0 High Speed (Mini B USB)
Power
- Input Voltage
+5V through USB connector or 12Pin connector
- Consumption
Less than 450 mA
Dimensions
50 (W) x 50 (H) x 40.8 (D) mm
Lens Mount
C Mount
Input / Output Connector
12 Pin Connector (Hirose) / 2.5 mm Pin Jack
Tripod
1/4”-20UNC depth 7 screw hole on top and bottom case, 4-M4 depth 4 screw holes on top and bottom case, 2-M4 depth 4 screw holes on both side of case
Weight
Approximately 112 g
Temperature
- Operational
Temperature: 0 to 40 deg. C, RH: 0 to 85% (No condensation)
- Storage
Temperature: -30 to 65 deg. C, RH: 0 to 90% (No condensation)
Vibration
20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each
Shock
Acceleration 70G, half amplitude 6ms, 3 directions 3 times each
Standard Compliancy
EMS :EN61000-6-2, EMI :EN61000-6-3 (Class B)
RoHS
RoHS Compliant
 
 
 

USB 2.0 (Standard) Board
ColorMonoSensorFormatResolutionFPSSize
STC-TC33USB-BSTC-TB33USB-B1/3"VGA640 x 4806045 x 45 x Var. mm
STC-TC83USB-BSTC-TB83USB-B1/3"XGA1024 x 7683045 x 45 x Var. mm
STC-TC133USB-BSTC-TB133USB-B1/3"SXVGA1280 x 9602245 x 45 x Var. mm
STC-TC152USB-BSTC-TB152USB-B1/2"SXGA1360 x 10242045 x 45 x Var. mm
STC-TC202USB-BSTC-TB202USB-B1/1.8"UXGA1620 x 12361545 x 45 x Var. mm

USB 2.0 (Standard) Cased
ColorMonoSensorFormatResolutionFPSSize
STC-TC33USB-ASTC-TB33USB-A1/3"VGA640 x 4806051 x 51 x Var. mm
STC-TC83USB-ASTC-TB83USB-A1/3"XGA1024 x 7683051 x 51 x Var. mm
STC-TC133USB-ASTC-TB133USB-A1/3"SXVGA1280 x 9602251 x 51 x Var. mm
STC-TC152USB-ASTC-TB152USB-A1/2"SXGA1360 x 10242051 x 51 x Var. mm
STC-TC202USB-ASTC-TB202USB-A1/1.8"UXGA1620 x 12361551 x 51 x Var. mm

USB 2.0 (Ultra-Small)
ColorMonoSensorFormatResolutionFPSSize
STC-MC33USBSTC-MB33USB1/3"VGA640 x 4806028 x 28 x 37 mm
STC-MC83USBSTC-MB83USB1/3"XGA1024 x 7683028 x 28 x 37 mm
STC-MC133USBSTC-MB133USB1/3"SXVGA1280 x 9602228 x 28 x 37 mm
STC-MC152USBSTC-MB152USB1/2"SXGA1360 x 10242028 x 28 x 42 mm
STC-MC202USBSTC-MB202USB1/1.8"UXGA1620 x 12361528 x 28 x 42 mm

USB 2.0 ("AH") Soft and Hard Triggering
(The USB signal is output over the USB connector)
ColorMonoSensorFormatResolutionFPSSize
STC-TC33USB-AHSTC-TB33USB-AH1/3"VGA640 x 4806050 x 50 x 35.8 mm
STC-TC83USB-AHSTC-TB83USB-AH1/3"XGA1024 x 7683050 x 50 x 35.8 mm
STC-TC133USB-AHSTC-TB133USB-AH1/3"SXVGA1280 x 9602250 x 50 x 35.8 mm
STC-TC152USB-AHSTC-TB152USB-AH1/2"SXGA1360 x 10242050 x 50 x 35.8 mm
STC-TC202USB-AHSTC-TB202USB-AH1/1.8"UXGA1620 x 12361550 x 50 x 35.8 mm

USB 2.0 ("ASH") Soft and Hard Triggering
(The USB signal is output over the 12pin connector)
ColorMonoSensorFormatResolutionFPSSize
STC-TC33USB-ASHSTC-TB33USB-ASH1/3"VGA640 x 4806050 x 50 x 35.8 mm
STC-TC83USB-ASHSTC-TB83USB-ASH1/3"XGA1024 x 7683050 x 50 x 35.8 mm
STC-TC133USB-ASHSTC-TB133USB-ASH1/3"SXVGA1280 x 9602250 x 50 x 35.8 mm
STC-TC152USB-ASHSTC-TB152USB-ASH1/2"SXGA1360 x 10242050 x 50 x 35.8 mm
STC-TC202USB-ASHSTC-TB202USB-ASH1/1.8"UXGA1620 x 12361550 x 50 x 35.8 mm
 
 
Comparison Chart
Model TB33USB-ASH TB83USB-ASH TB133USB-ASH TB152USB-ASH TB202USB-ASH
Resolution VGA (0.3MP) XGA (0.8MP) SXGA (1.25MP) SXGA (1.3MP) UXGA (2MP)
Image Sensor 1/3" 1/3" 1/3" 1/2" 1/1.8"
Frame Rate 60 30 22 19 15
Picture Element 648 x 480 1024 x 768 1280 x 960 1280 x 1024 1600 x 1200
Dimension 50 x 50 x 35.8
 
 

STC-TB152USB-ASH

Mechanical
 
STC-TB152USB-ASH
SXGA, Monochrome Camera
 
DownloadTypeSoftwareNotes
1DriversStStream(v1.00.4140).zipDirectX driver for USB series
1DriversDriver_HALCON.zipHalcon drivers for USB series
1DriversDriver_LabView.zipLabView driver for USB series
1DriversSentech-3.0.7.tgzLinux driver for USB series
1SDK'sNormalSDK(v1.10).zipSDK (Software Development Kit) for Standard USB cameras
1SDK'sTriggerSDK(v1.06).zipSDK (Software Development Kit) for Hardware Trigger USB cameras
1SoftwareStCamSWare(v1.10).zipViewing Software for the USB series
* Please contact your sales representative for this download.
 
 
DownloadTypeDocumentsNotes
1CertificationCE_USB(ASH).pdfCE Declaration for the USB "ASH" series
1Manualssofm_USB_de_v1.10.pdfGerman Software Manual for USB Camera Viewing Software (StCamSWare)
1Manualssofm_USB_es_v1.10.pdfSpanish Software Manual for USB Camera Viewing Software (StCamSWare)
1Manualssdkm_STD-USB_en_ver1.10.pdfSDK Manual for Standard USB cameras
1Manualssdkm_TRG-USB_en_ver1.06.pdfSDK Manual for Trigger USB cameras
1Manualssofm_USB_en_v1.10.pdfEnglish Software Manual for StCamSWare (USB Viewing Software)
1Specificationsspec_STC-TB_TC152USB_ASH_en_v3.0.pdfSpecification sheet for the 1.3MP (SXGA) USB "ASH" cameras
* Please contact your sales representative for this download.
 
 

Terms and Licensing:

USE OF THE SOFTWARE IS SUBJECT TO THE SENSOR TECHNOLOGIES CO., LTD. (SENTECH) SOFTWARE LICENSE TERMS SET FORTH HEREIN. USING THE SOFTWARE INDICATES YOUR ACCEPTANCE OF THESE LICENSE TERMS. IF YOU DO NOT ACCEPT THESE LICENSE TERMS, YOU MUST RETURN THE SOFTWARE FOR A FULL REFUND (IF APPLICABLE). IF THE SOFTWARE IS SUPPLIED WITH ANOTHER PRODUCT YOU MAY RETURN THE ENTIRE UNUSED PRODUCT FOR FULL REFUND.
SENTECH SOFTWARE LICENSE TERMS:
The following License Terms govern your use of the accompanying Software unless you have a separate written agreement with SENTECH.
License Grant
SENTECH grants you a license to Use one copy of the Software. Use means storing, loading, installing, executing or displaying the Software. You may not modify the Software or disable any licensing or control features of the Software. The SDK and included drivers may be used to interface to third party software or to generate original code, but the use of the SDK or included drivers in no way negates or modifies the terms and conditions of this Software License.
Ownership
The software is owned and copyright by SENTECH. Your license confers no title or ownership in the Software and is not a sale of any rights in the Software.
Copies and Adaptations
You may only make copies or adaptations of the Software for archival purposes or when copying or adaptation is an essential step in the authorized Use of the Software. You must reproduce all copyright notices in the original Software on all copies or adaptations. You may not copy the Software onto any bulletin board or similar system.
No Disassembly or Decryption
You may not disassemble or decompile the Software unless Sentech's prior written consent is obtained. Upon request, you will provide SENTECH with reasonably detailed information regarding any disassembly or decompilation. You may not decrypt the Software unless decryption is necessary part of the operation of the Software.
Transfer
Your license will automatically terminate upon any transfer of the Software. Upon transfer, you must deliver the Software including any copies and related documentation, to the transferee. The transferee must accept these License Terms as a condition to the transfer.
Termination
SENTECH may terminate your license upon notice for failure to comply with any of these License Terms. Upon termination, you must immediately destroy the Software, together with all copies, adaptations and merged portions in any form.
US Government Restricted Rights