Progressive Scan (Remote Head)

 
Progressive Scan  ...  Resolutions  (60fps • 90fps)    
 
 

 

STC-SS1200

Progressive Scan, VGA, Remote Head

The STC-SS1200 series was designed for high speed applications where size and weight are extremely critical. The remote head design features a light, compact head so that a minimum amount of inertia is generated during very fast stop/start XYZ type movements. The STC-SS1200 series offers high speed triggering with 60fps analog output, utilizing a VGA progressive scan format.

1/3" VGA Progressive Scan CCD
Ultra-Compact Remote Head
Triggering at 60fps

 

Back   

Select Options  
 

Name

Specifications
Model No
STC-SS1200
Imager
⅓” Interline XGA Monochrome Progressive CCD: ICX204AL
Total Picture Element
1077 (H) x 788 (V)
Effective Picture Element
1034 (H) x 779 (V)
Active Picture Element
XGA: 1024 (H) x 768 (V)
Chip Size
5.8 (H) x 4.92 (V) mm
Cell Size
4.65 (H) x 4.65 (V) µm
Scanning System
Progressive
Scanning Method
Full Scanning, Partial Full Scanning, ½ Partial Scanning, ¼ Partial Scanning, Variable Partial Scanning, Binning, Binning Partial Scanning, Binning ½ Partial Scanning, Binning ¼ Partial Scanning, Binning Variable Partial Scanning
Vertical Frequency (Frame Rate)
29.59 Hz
Horizontal Frequency
23.23 kHz
Pixel Frequency
29.5 MHz
S/N Ratio (Standard Deviation)
56 dB (GAIN 0 dB)
Minimum Scene Illumination
1 Lux at F1.4
Sync System
Internal / External
Video Output
1.0 Vp-p / 75Ω, DC Coupling (0V)
Shutter Speed
- Dip Switch
OFF; 1/200; 1/500; 1/1000; 1/2000; 1/4000; 1/8000; 1/20,000 sec
- Communication
OFF; ½ to 100,000 sec. (Variable at every H and Clock)
Gain
0 to 27 dB
Gamma
1.0 / 0.45
Power Supply
- Input Voltage
DC 12V ± 10%
- Consumption
Less than 1.8W
Trigger Mode
Edge Preset Trigger (V-reset, Non-reset) Pulse Width Trigger (V-reset, Non-reset)
Communication
RS232 via 12 Pin Connector
Dimensions
28 (W) x 28 (H) x 46.3 (D)mm including lens mount and the connector
Optical Filter
No IR Cut Filter
Optical Center Accuracy
Positional Accuracy in H and V directions: +/- 0.31 mm
Material
- Case
Front, Base, and Rear: Aluminum Die Cast (ADC12) Cover: Steel Sheet Covered with Zinc
- Tripod
Polycarbonate ABS
Lens Mount
C Mount
Interface Connector
HR10A-10R-12PB (Hirose) or equivalent
Tripod
Tripod can be attached to 4 plates (4 screws on the bottom plate, 3 screws on the other 3 plates)
Weight
Approximately 52g (Camera: 43g, Tripod: 9g)
Temperature and Humidity
- Operational
Temperature: -5 to 50 deg C; Relative Humidity: 0 to 85% (No Condensation)
- Storage
Temperature: -30 to 65 deg C; Relative Humidity: 0 to 90% (No Condensation)
Vibration
20Hz to 200Hz to 20Hz (5 min./cycle), Acceleration 10G, 3 Directions 30 Minutes Each
Shock
Acceleration 70G, Half Amplitude 6 ms, 3 Directions 3 Times Each
Standard Compliancy
EMS: EN61000-6-2, EMI: EN55011 (Class B)
RoHS
RoHS Compliant
 
 
 
 

Progressive Scan Series

Board, Cased, Cube and Remote Head Models

Sentech’s line of Progressive Scan analog Machine Vision cameras is powerful and versatile. This line up starts with our Cube Cameras series. The case of these cameras are approximately a one inch cube. They feature VGA (0.3MP) to UXGA (2MP) resolutions with full machine vision functionality. Next in the line up are the “SS” series of remote head cameras. These are high speed VGA cameras with a very small remote head for applications where weight, space and inertia control are critical. Finally, Sentech offers a board version with a face dimension of 30 x 30mm featuring full MV functionality.

Board Cameras (Compact)
MonoSensorFormatResolutionLens MountFPSSize
STC-331/3"VGA648 x 494CS Mount30, 6030 x 30 x 32 mm
STC-831/3"XGA1024 x 768CS Mount3030 x 30 x 32 mm
 

Cased Cube Cameras (Compact)
MonoSensorFormatResolutionLens MountFPSSize
STC-A33A1/3"VGA648 x 494CS Mount30, 60, 9028 x 28 x 46.3 mm
STC-A83A1/3"XGA1024 x 768CS Mount3028 x 28 x 46.3 mm
STC-A152A1/2"SXGA1360 x 1040CS Mount15, 1928 x 28 x 46.3 mm
STC-A202A1/1.8"UXGA1620 x 1220CS Mount1528 x 28 x 46.3 mm
 

Cased Cameras (Remote Head)
MonoSensorFormatResolutionLens MountFPSSize
STC-SS12001/3"VGA648 x 494Special Mount60110 x 80 x 28 mm
STC-SS1200-901/3"VGA648 x 494Special Mount90110 x 80 x 28 mm
 
 
Comparison Chart
Models STC-SS1200 STC-SS1200-90
Image Sensor 1/3" 1/3"
Resolution VGA XGA
Resolution 648 x 494 1024 x 768
Frame Rate 30, 60 30
Dimension 110 x 80 x 28 mm
 
 
Mechanical
Mechanical Remote
 
STC-SS1200
Progressive Scan, VGA, Remote Head
 
* Please contact your sales representative for this download.
 
 
* Please contact your sales representative for this download.
 
 

Terms and Licensing:

USE OF THE SOFTWARE IS SUBJECT TO THE SENSOR TECHNOLOGIES CO., LTD. (SENTECH) SOFTWARE LICENSE TERMS SET FORTH HEREIN. USING THE SOFTWARE INDICATES YOUR ACCEPTANCE OF THESE LICENSE TERMS. IF YOU DO NOT ACCEPT THESE LICENSE TERMS, YOU MUST RETURN THE SOFTWARE FOR A FULL REFUND (IF APPLICABLE). IF THE SOFTWARE IS SUPPLIED WITH ANOTHER PRODUCT YOU MAY RETURN THE ENTIRE UNUSED PRODUCT FOR FULL REFUND.
SENTECH SOFTWARE LICENSE TERMS:
The following License Terms govern your use of the accompanying Software unless you have a separate written agreement with SENTECH.
License Grant
SENTECH grants you a license to Use one copy of the Software. Use means storing, loading, installing, executing or displaying the Software. You may not modify the Software or disable any licensing or control features of the Software. The SDK and included drivers may be used to interface to third party software or to generate original code, but the use of the SDK or included drivers in no way negates or modifies the terms and conditions of this Software License.
Ownership
The software is owned and copyright by SENTECH. Your license confers no title or ownership in the Software and is not a sale of any rights in the Software.
Copies and Adaptations
You may only make copies or adaptations of the Software for archival purposes or when copying or adaptation is an essential step in the authorized Use of the Software. You must reproduce all copyright notices in the original Software on all copies or adaptations. You may not copy the Software onto any bulletin board or similar system.
No Disassembly or Decryption
You may not disassemble or decompile the Software unless Sentech's prior written consent is obtained. Upon request, you will provide SENTECH with reasonably detailed information regarding any disassembly or decompilation. You may not decrypt the Software unless decryption is necessary part of the operation of the Software.
Transfer
Your license will automatically terminate upon any transfer of the Software. Upon transfer, you must deliver the Software including any copies and related documentation, to the transferee. The transferee must accept these License Terms as a condition to the transfer.
Termination
SENTECH may terminate your license upon notice for failure to comply with any of these License Terms. Upon termination, you must immediately destroy the Software, together with all copies, adaptations and merged portions in any form.
US Government Restricted Rights