CameraLink Cameras

 
CameraLink  ...  Resolutions  (VGA • XGA • XGA (44fps) • SXGA • UXGA • UXGA (30fps) • QSXGA)    
 
 

 

STC-POCLC232A

UXGA, Color Camera

The STC-POCLC232A is a full featured, cost effective, UXGA, progressive scan, digital Power Over CameraLink® cube camera with a 1/1.8" color CCD with RGB Primary Color Filter. This camera features a full frame, 30fps, UXGA output, partial scanning, triggering, and reset capabilities.
1/1.8" CCD Image Sensor
UXGA, Progressive Scan, 30fps
Power Over Camera Link

 

Back    Front    Right    Left   

Select Options  
 

Name

Specifications
Model No
STC-POCLC232A
Imager
1/1.8” Interline UXGA Color Progressive CCD: ICX274AQ
Total Picture Element
1688 (H) x 1248 (V)
Active Picture Element
1620 (H) x 1236 (V)
Chip Size
8.5 (H) x 6.8 (V) mm
Cell Size
4.4 (H) x 4.4 (V) µm
Scanning System
Progressive
Scanning Method
Full, Partial full, ½ partial, ¼ partial, Variable partial
Vertical Frequency (Frame Rate)
30.854 Hz
Horizontal Frequency
38.352 kHz
Pixel Frequency
73.636 MHz
S/N Ratio
- @ 8bit output
≤ 4 Digit (Gain 0 dB)
- @ 10bit output
≤ 15 Digit (Gain 0 dB)
Minimum Scene Illumination
0.92 Lux @ F1.2, 50 IRE
Sync System
Internal / External
Video Output
Digital 8 or 10 bit CameraLink® (Base Configuration)
Tap
2 Tap (The frequency of the clock output at CameraLink: 36.818 MHz)
Shutter Speed
OFF, 1/9 to 1/240,000 sec. (Variable at every H and clock)
Gain
0 ~ 25dB
Gamma
1.0
Power
- Input Voltage
12 Vdc ± 10% via Camera Link connector
- Consumption
< 4.0 W
Trigger Mode
Edge Preset Trigger (V-reset, Non-reset)’; Pulse Width Trigger (V-reset, Non-reset)
Communication
RS232 via Camera Link connector
Dimensions
28 (W) x 28 (H) x 53.5 (D) mm (including lens mount and the connector)
Optical Filter
No IR cut filter
Optical Center Accuracy
Positional accuracy in H and V directions: +/- 0.31 mm Rotational accuracy of H and V: +/- 2.1 deg.
Material
- Case
Front, base, and rear: Aluminum die cast (ADC 12) Cover: Steel sheet covered with zinc
- Tripod
Polycarbonate ABS
Lens Mount
C mount
Interface Connector
HR 10A-7R-6PB (Hirose) or equivalent
Tripod
Tripod can be attached to 4 plates (4 holes on the bottom plate, 3 holes on the other 3 plates)
Weight
Approximately 75.5g (Camera: 65.5g, Tripod: 10g)
Temperature and Humidity
- Operating
Temperature: -5 to 40 deg C; Relative Humidity: 0 to 85% (No condensation)
- Storage
Temperature: -30 to 65 deg C; Relative Humidity: 0 to 90% (No condensation)
Vibration
20Hz to 200Hz to 20Hz (5min./cycle); Acceleration 10G, 3 directions 30 min. each
Shock
Acceleration 70G, half amplitude 6ms, 3 directions 3 times each
Standard Compliancy
EMS: EN61000-6-2, EMI: EN55011 (Class B)
RoHS
RoHS Compliant
 
 
 

Cube CameraLink Models
ColorMonoSensorFormatResolutionFPSSize
STC-CLC33ASTC-CL33A1/3"VGA648 x 49430, 60, 9028 X 28 X 40 mm
STC-CLC83ASTC-CL83A1/3"XGA1024 x 7683028 X 28 X 40 mm
STC-CLC83A-44STC-CL83A-441/3"XGA1024 x 7684428 X 28 X 40 mm
STC-CLC152ASTC-CL152A1/2"SXGA1360 x 102415, 1928 X 28 X 40 mm
STC-CLC202ASTC-CL202A1/1.8"UXGA1620 x 12201628 X 28 X 40 mm
STC-CLC232ASTC-CL232A1/1.8"UXGA1620 x 12363028 X 28 X 47 mm
STC-CLC500ASTC-CL500A2/3"QSXGA2448 x 20581635 x 35 x 40.7 mm

Cube CameraLink (Kodak Sensor) Models
ColorMonoSensorFormatResolutionFPSSize
STC-CLC338ASTC-CL338A1/3" (Kodak)VGA644 x 48424035 X 35 X 48.2 mm

Power Over CameraLink Models
ColorMonoSensorFormatResolutionFPSSize
STC-POCLC33ASTC-POCL33A1/3"VGA648 x 49430, 60, 9028 X 28 X 40 mm
STC-POCLC83ASTC-POCL83A1/3"XGA1024 x 7683028 X 28 X 40 mm
STC-POCLC83A-44STC-POCL83A-441/3"XGA1024 x 7683028 X 28 X 40 mm
STC-POCLC152ASTC-POCL152A1/2"SXGA1360 x 102415, 1928 X 28 X 40 mm
STC-POCLC202ASTC-POCL202A1/1.8"UXGA1620 x 12201628 X 28 X 40 mm
STC-POCLC232ASTC-POCL232A1/1.8"UXGA1620 x 12363028 X 28 X 47 mm
STC-POCLC500ASTC-POCL500A2/3"QSXGA2448 x 20581635 x 35 x 40.7 mm

Cube Remote Head CameraLink Models
ColorMonoSensorFormatResolutionFPSSize
STC-RCLC33A-C3STC-RCL33A-C31/3"VGA648 x 49430, 60, 9028 X 28 X 40 mm

Rectangular Remote Head CameraLink Models
ColorMonoSensorFormatResolutionFPSSize
STC-RCLC33A-R3STC-RCL33A-R31/3"VGA648 x 49430, 60, 9028 X 28 X 40 mm
 
 
Comparison Chart
Models POCLC33A POCLC83A POCLC83A-44 POCLC152A POCLC202A POCLC232A POCLC500A
Resolution VGA (0.3MP) XGA (0.8MP) XGA (0.8MP) SXGA (1.3MP) UXGA (2MP) UXGA (2MP) QSXGA (5MP)
Image Sensor 1/3" 1/3" 1/3" 1/2" 1/1.8" 1/1,8" 2/3"
Frame Rate 30, 60, 90 30 44 15, 19 16 30 16
Picture Element 648 x 494 1024 x 768 1024 x 768 1360 x 1024 1620 x 1220 1620 x 1236 2448 x 2058
Dimension 28 x 28 x 29.5 28 x 28 x 36.5 35 x 35 x 30.2
 
 
Mechanical
 
STC-POCLC232A
UXGA, Color Camera
 
DownloadTypeSoftwareNotes
1SoftwareCLCtrl2 ver1.0.0.0.zipControl Software for the CameraLink series
* Please contact your sales representative for this download.
 
 
DownloadTypeDocumentsNotes
1Specificationsspec_STC-POCL_POCLC232A_en_v1.7.pdfSpecification sheet for the 2MP (UXGA) Power Over CameraLink camera
1User Guidesusers_STC-POCL_POCLC232A_en_v1.1.pdfUser Guide for the 2MP (UXGA) Power Over CameraLink camera
* Please contact your sales representative for this download.
 
 

Terms and Licensing:

USE OF THE SOFTWARE IS SUBJECT TO THE SENSOR TECHNOLOGIES CO., LTD. (SENTECH) SOFTWARE LICENSE TERMS SET FORTH HEREIN. USING THE SOFTWARE INDICATES YOUR ACCEPTANCE OF THESE LICENSE TERMS. IF YOU DO NOT ACCEPT THESE LICENSE TERMS, YOU MUST RETURN THE SOFTWARE FOR A FULL REFUND (IF APPLICABLE). IF THE SOFTWARE IS SUPPLIED WITH ANOTHER PRODUCT YOU MAY RETURN THE ENTIRE UNUSED PRODUCT FOR FULL REFUND.
SENTECH SOFTWARE LICENSE TERMS:
The following License Terms govern your use of the accompanying Software unless you have a separate written agreement with SENTECH.
License Grant
SENTECH grants you a license to Use one copy of the Software. Use means storing, loading, installing, executing or displaying the Software. You may not modify the Software or disable any licensing or control features of the Software. The SDK and included drivers may be used to interface to third party software or to generate original code, but the use of the SDK or included drivers in no way negates or modifies the terms and conditions of this Software License.
Ownership
The software is owned and copyright by SENTECH. Your license confers no title or ownership in the Software and is not a sale of any rights in the Software.
Copies and Adaptations
You may only make copies or adaptations of the Software for archival purposes or when copying or adaptation is an essential step in the authorized Use of the Software. You must reproduce all copyright notices in the original Software on all copies or adaptations. You may not copy the Software onto any bulletin board or similar system.
No Disassembly or Decryption
You may not disassemble or decompile the Software unless Sentech's prior written consent is obtained. Upon request, you will provide SENTECH with reasonably detailed information regarding any disassembly or decompilation. You may not decrypt the Software unless decryption is necessary part of the operation of the Software.
Transfer
Your license will automatically terminate upon any transfer of the Software. Upon transfer, you must deliver the Software including any copies and related documentation, to the transferee. The transferee must accept these License Terms as a condition to the transfer.
Termination
SENTECH may terminate your license upon notice for failure to comply with any of these License Terms. Upon termination, you must immediately destroy the Software, together with all copies, adaptations and merged portions in any form.
US Government Restricted Rights